Upgrade Engine
Upgrade your 1998 through 2010 Gen 3 or 4 engine with this new 625 HP 427 cubic inch powerhouse specifically designed to replace an existing LS engine. Assembled with a new block and Blueprint heads, forged crank, rods, and pistons. The engine includes a performance hydraulic roller cam and lifters and upgraded roller rockers. Built with a Gen 4 style 58x reluctor and sensors, this engine is a drop in for Gen 4 applications, and by using Blueprint's conversion kit (sold separately), you can also install into earlier Gen 3 applications. 91 octane or better recommended. Engine includes intake manifold, timing cover, valley cover, and rear cover. Injectors, rails, throttle body, coil packs, valve covers, water pump, and oil pan NOT included. In many cases, original parts can be used.
Recommended Stall Converter: 2200+ RPM
Recommended Fuel: 91 Octane
- New block with 1-piece rear main seal
- New Blueprint Cylinder Heads p/n 138-PS8015 with roller rocker arms
- Recommended Spark Plugs: ACDelco 41-985
- GM L92 Intake
Rotating Assembly
- Forged Crankshaft: 4.125" Stroke
- Forged Connecting Rods: 6.125"
- Mahle Forged Pistons
- 11:1 Compression
- Internally Balanced Camshaft Specs
- Hydraulic Roller
- Duration at .050'' Lift: 239 Intake, 255 Exhaust
- Lift: .624'' Intake, .624'' Exhaust
- Lobe Separation: 114°
Engine Break-In Procedure
Use or break-in oil or conventional (non-synthetic) multi-viscosity oil with zinc additive for the first 500 miles of operation. Avoid hard acceleration for sustained periods. Periodically change the engine speed while driving to help seat the rings. While the engine is running, be sure to check oil pressure and coolant temperature, and check for fluid leaks, such as oil, transmission fluid, fuel, and coolant/antifreeze. Also listen for any unusual sounds. Should you hear an unusual sound, shut the engine off, check for the source, and correct it.
Engines with flat tappet cams only - Start the engine and bring it to 2,000 RPM. Get the engine running smoothly. Then vary the engine speed from 1,800-2,200 RPM in a slow acceleration/deceleration cycle for 30 minutes. This is necessary to provide adequate oil splash and lifter rotation to properly mate each lifter to its lobe.
At 500 Miles change the engine oil and filter using conventional (non-synthetic) oil. After 6,000 miles, synthetic oils can be used in your engine. For flat tappet cam engines, continued use of oil with zinc or a zinc additive for the life of your engine is recommended.
Specifications:
What are the horsepower limits of this engine if adding boost(most likely around 10psi give or take)?
Will it fit in a c6 corvette z06?
Will this be a plug and play other than tuning for my 2011 corvette? And what size throttle body does it take to make that power?
Can I use this motor with a holly terminator x max in a 97 camaro rs as a swap
So I’m wanting to use this motor for my drift car using all ls1 accessories and headers will this work or no since it’s based off the ls3
What is the max hp rating for this motor? I'm looking to build a 427 with a Kenne bell 3.6 SC and should be right around 1000-1100 whp.
will this replace my 5.3 motor in my 01 Tahoe ? with exception of long block parts as listed , and what about an ECM,, thank you
is this a direct swap from my ls3 callaway sc540 ecu tunning and supercharger?
Motor Vehicles
WARNING: Motor vehicles contain fuel, oils and fluids, battery posts, terminals and related accessories which contain lead and lead compounds and other chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. These chemicals are found in vehicles, vehicle parts and accessories, both new and as replacements. When being serviced, these vehicles generate used oil, waste fluids, grease, fumes and particulates, all known to the State of California to cause cancer, birth defects, and reproductive harm.
Tools:
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically treated lumber. Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
Electrical Cords
WARNING: The wires of these products contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.